Fiamma F45s Not Closing on One Side: Presto Fix Adjustment
Quick answer
When a Fiamma F45s will not close on one side, first look at which end is open and whether the lead bar is level. If the end away from the crank stays open and the bar is level, the canopy has gone slack on that side. Fiamma's fix is the Presto Fix at that end of the roller: unroll the awning fully and turn its ring nut clockwise one or two notches with a flat screwdriver, then use it "with moderation". If the bar sits lower on one side when open, adjust the upper bolt of the Dual Shock Absorber on the low side with a 10 mm wrench. Fiamma's F45s manual says the Fiamma ZIP has no Presto Fix. If the crank end is the one left open, the Presto Fix does not reach it.
If your Fiamma F45s won't close on one side, check two things: which end is open, and whether the lead bar is level. If the end away from the crank handle stays open and the bar is level, the fabric has gone slack on that side, and Fiamma's fix is the Presto Fix. Unroll the awning all the way, then use a flat screwdriver to turn the Presto Fix on that end "clockwise (downwards) of one or two shots," where a shot is one notch on the cap. If the lead bar hangs lower on one side when the awning is open, the fix is different: adjust the upper bolt of the Dual Shock Absorber on the low side with a 10 mm wrench. One more check comes first: Fiamma's F45s manual says "In Fiamma ZIP there is no Presto Fix."
Below are the parts named in Fiamma's manuals, a table of what you see and what to do, and the steps for each fix. After that come the less common causes: a knock or a gust of wind, an arm that droops into the case, and a canopy that has stretched too far for the Presto Fix to take up. For RV awnings from other makers, start with RV awning adjustment.
What the F45s parts are called
Fiamma F45s. A roll-up box awning from Fiamma, an Italian maker, built for vans and motorhomes. It mounts on the side wall, and Fiamma sold it in lengths from 190 to 450 cm (about 75 to 177 in). When it is closed, the fabric is wound on a roller inside an aluminum case, and the two folding arms fold away under it. You open and close it with a crank handle, unless a motor kit is fitted.
Lead bar. The long bar on the front edge of the fabric. Fiamma also calls it the front profile. When the awning closes, the lead bar pulls up against the case and shuts it, so "not closing on one side" means one end of this bar sits out from the case.
Winch. Fiamma's word for the crank end of the awning, where the handle hooks in. This matters because the Presto Fix is at the other end.
Presto Fix. A round adjuster on the end of the roller tube, at the end opposite the winch. Fiamma calls it the "roller regulation cap". It has a ring nut you turn with a flat screwdriver and a row of notches that hold it in place, and Fiamma's manual says that turning the ring nut clockwise makes the flange behind it "move widening." In plain words, that end of the roller gets a little fatter so the fabric winds on thicker there and pulls that end of the lead bar in tighter. Fiamma's catalog says it is there "to guarantee a perfect closing over time."
Dual Shock Absorber. The bracket where each arm joins the case. Fiamma's catalog calls it a "shock absorbing bracket with dual bolt system to protect the awning and the vehicle during bad weather." It has an upper and a lower bolt, and Fiamma's fix for a lead bar that sits low on one side is made at the upper bolt.
Red flag. A red marker at each end of the lead bar. Fiamma's troubleshooting guide says it shows while the awning is open and is "no longer visible" once the awning is fully closed. If a red flag still shows at one end after you close the awning, that end is not closed.
Fiamma F45s not closing on one side: fix by symptom
Each row comes from a Fiamma document or an owner thread named in the sections below.
| What you see | Likely cause | What to do |
|---|---|---|
| End away from the crank stays open; bar level when the awning is out | Canopy slack on that side (Fiamma installation manual) | Presto Fix: ring nut clockwise, one or two notches, awning fully out |
| Lead bar lower on one side when the awning is out | That arm has dropped (Fiamma maintenance manual) | Upper bolt of the Dual Shock Absorber on the low side, 10 mm wrench, small turns |
| First time out, far end won't sit flush | Fabric wound on unevenly, or support legs not clipped in (owner threads) | Clip the legs in, wind it fully out, then back in |
| Problem started after a gust or a knock | Shock absorber bolts stuck in the upper slots, or the absorber broken | Check the bolts move freely; replace a broken absorber |
| Crank end stays open | Not a Presto Fix job; that end has no adjuster | Check the arm on that side first; then see the stretched canopy section |
| Fiamma ZIP | No Presto Fix on that model (F45s manual) | Use the arm and canopy fixes |
First, find which end is open and look at the bar
This step saves the most time. Most owners reach for the Presto Fix first, and often that is right, but it only works on one end and only for one cause.
Close the awning and look at both ends of the lead bar, because a red flag that still shows tells you that end is open. Now open the awning all the way and look at the bar from a few steps back to see whether it is level or one end is lower.
- Bar level, open end is away from the crank. This is the Presto Fix case. Go to the next section.
- Bar low on one side. Fix the arm first with the shock absorber bolt, then close it and check again before you touch the Presto Fix.
- Open end is the crank end. The Presto Fix cannot help here, because it sits at the other end.
Fiamma's maintenance manual shows the problem on the left side and the fix on "the left side of the Presto Fix." Its troubleshooting guide names the same problem as "lead bar not closing on the side opposite the winch." Both describe one end only: the end that has the adjuster. So "turn the Presto Fix on whichever side is open" is only half right, because it holds only when the open side is the end away from the crank.
The Presto Fix adjustment, step by step
Fiamma's installation manual explains why this is needed: "over a period of time, the canopy could become slack on the sides and the closing may not be perfect." The steps below come from Fiamma's F45s maintenance manual (10 minutes, one person) and its installation manual.
- Unroll the awning completely. Fiamma's steps start with the awning fully out, which is where you can reach the end of the roller.
- Find the Presto Fix. It is the round cap on the end of the roller tube, at the end opposite the crank.
- Use a flat screwdriver. Set it on the ring nut, the part with the notches.
- Turn it clockwise, downwards. Move it one notch. Fiamma's limit is "one or two shots," so two notches is the most you should try.
- Close the awning and check. Look for the red flag at that end, and if it has gone, the end is closed.
- Second notch only if needed. If the end is better but still open, unroll the awning again and turn it one more notch.
Use it with moderation: those are Fiamma's words. The installation manual says the Presto Fix is "only for this problem," a canopy that has gone slack on the sides. It is not a cure for a bent arm or a dropped bar, so if two notches do not close the end, stop and look for another cause.
Lead bar low on one side: the 10 mm shock absorber bolt
Fiamma's maintenance manual calls this problem "lead bar inclined." The lead bar "is lower on one side (left or right)," and a low end can stop that end from seating when the awning closes. It is a 5 minute, one-person job, and the fix is:
- Check the bolts first. Fiamma's warning: "Ensure that shock absorber bolts are not blocked in the upper slots."
- Find the low side. Make the adjustment on the side where the lead bar is lower, not on the high side.
- Turn the upper bolt. With a 10 mm wrench, adjust "the upper bolt of the Dual Shock Absorber by tightening or loosening slightly."
- Check the bar. Open the awning and look again, since Fiamma's installation manual says to "make sure that the front profile comes out horizontally when unrolling the awning."
The installation manual adds one rule: "For arms and fabric adjustments, please use only the depicted top bolt." So leave the lower bolt alone. On the MotorhomeFun forum, an owner whose F45s needed "a little push up on the left hand side" was told the fix was "the top bolt of the shock absorber where the arm fixes needed loosening off a little bit."
An arm drooping into the case
Fiamma's installation manual has a section called "arm adjustment." It says "the arm may lower itself with wear and tear over time." A low arm leaves the lead bar low on that side when the awning is open, and it can keep that end of the bar from pulling up to the case.
The fix is the same top bolt. Fiamma's words are "Screw/unscrew nut A to reposition the arm." The same section says to use "only the depicted top bolt" for arm and fabric adjustments. Turn it a little, open the awning, and check that the lead bar comes out level, then close it and look for the red flags. Do this before you turn the Presto Fix, because a notch on the Presto Fix can mask a low arm without fixing it.
After a gust of wind or a knock
If the awning closed fine until a windy day or a bump, look at the Dual Shock Absorber on that side first, since Fiamma built it to take that kind of load. Its troubleshooting guide says it "functions as a damper, and if it should break, serious damages on the awning are avoided."
There are two things to check. First, the bolts: Fiamma's warning that they must not be "blocked in the upper slots" is the first line of the lead bar fix. Second, the part itself: if it is cracked or bent, it is meant to be replaced, and Fiamma's troubleshooting guide has a page on replacing it. Fiamma's maintenance manual lists 10 and 13 mm wrenches for its repairs. Bolts that are free and an absorber that is whole bring you back to the 10 mm upper bolt adjustment above.
Fiamma's troubleshooting guide asks you to roll the awning up in rain, wind or snow. For when to bring an RV awning in, see RV awning care and wind safety. If an arm is bent rather than out of adjustment, see awning arm replacement.
New awning, or first time this season
A common case on owner forums is an awning that will not sit flush the first time it is used. On the T6 Forum (a VW Transporter owners site), a new F45s owner wrote that "the far end just won't sit flush." Two simple fixes came back from other owners before anyone touched an adjuster.
- Clip the legs in. One owner said "if the legs aren't fully clipped back in it doesn't shut properly."
- Wind it fully out, then back in. Another said to "wind it fully out. Then in again," keeping a little tension on the fabric "(pulling out, but not too hard!)" as it goes in. A third owner wrote that this "sorted it."
A Fiamma representative, quoted on the Class B Forum, made one more point: the awning "does not 'lock' into place when it is closed, the same mechanism that" holds it open also holds it closed. So do not force a gap shut by hand; find the cause instead.
When the canopy has stretched too far
Fabric slackens with age, and that slack is what the Presto Fix is there to take up. If two notches do not close the end, or if the crank end is the one that stays open, the fabric may have more slack than the adjuster can cover.
A Class B Forum thread passed on a Fiamma representative's tip for an awning whose winder end stuck out. The tip was tape on the fabric edge at that corner to make the roller thicker there: "If your awning sticks out 3/4" then try 8" to 10" applied to the awning" fabric. The owner who posted it used Gorilla tape instead of duct tape because it is thicker. Treat this as a workaround passed on in a forum, not a Fiamma manual step, and expect to find the right length by trying.
The lasting fix is new fabric. Fiamma's maintenance manual gives fabric replacement as a 30 minute job for two people. For the general job on RV awnings, see RV awning fabric replacement.
The Fiamma ZIP: no Presto Fix
Fiamma's F45s installation manual ends its Presto Fix section with one line: "In Fiamma ZIP there is no Presto Fix." So on that model, skip the Presto Fix and go straight to the arm, wind and canopy fixes above.
Fiamma has used the ZIP name on more than one product. Its 2014 catalog lists Presto Fix as a feature of the Fiamma ZIP awning sold then, and an older ZIP series installation manual shows the Presto Fix step. If your awning is called a ZIP, look at the end of the roller opposite the crank. A round cap with a notched ring nut is a Presto Fix, and no cap means no Presto Fix.
Worked example: left end open on an F45s van awning
Take an F45s on a camper van with the crank at the right end. Suppose that after two seasons, the left end of the lead bar sits out from the case and its red flag still shows when the awning is closed. The right end closes fine.
Step 1: which end. The open end is the left, away from the crank, so the Presto Fix is in reach.
Step 2: is the bar level? Open the awning all the way and look. Suppose the left end of the bar hangs lower than the right, which means the arm comes first. Check that the shock absorber bolts on the left arm are not stuck in the upper slots, then turn the upper bolt a little with a 10 mm wrench until the bar comes out level.
Step 3: close and look. If the left red flag is gone, the job is done and the Presto Fix stays as it was.
Step 4: if the flag still shows. Now the bar is level and the end is still open, which is the slack canopy case. Unroll fully, turn the left Presto Fix one notch clockwise, and close again.
Step 5: stop at two. If a second notch still leaves the flag showing, stop turning, because the fabric is likely past what the Presto Fix can take up, so go to the stretched canopy fixes.
What this answer does not cover
These steps come from Fiamma's F45s maintenance and installation manuals and its troubleshooting guide, plus owner threads that are marked as such. They fit the crank-operated F45s, and Fiamma's other awnings, such as the F65 and F80, and the F45s with a motor kit may have different parts, so get the manual for your own model. Fiamma's documents give the turn direction for the Presto Fix but not how far one notch moves the bar, so test one notch at a time. They give no torque figure for the shock absorber bolt, so "slightly" is the only guide. If the case, the wall brackets or an arm is bent, no adjustment will close the awning properly. Have a Fiamma dealer look at it, and do not drive with an end hanging open. For an awning that is still under warranty, ask the dealer before you adjust anything.
For the general picture, see awning retracts unevenly and awning arms won't close. If the awning will not come in at all, see RV awning won't retract.
Key takeaways
- Find which end is open and whether the lead bar is level before you adjust anything.
- End away from the crank open, bar level: turn the Presto Fix clockwise one notch, with the awning fully out. Two notches at most.
- Bar low on one side: turn the upper Dual Shock Absorber bolt on the low side a little, with a 10 mm wrench. Leave the lower bolt alone.
- After wind or a knock, check that the shock absorber bolts are not stuck in the upper slots and that the absorber is not broken.
- Fiamma says the Fiamma ZIP has no Presto Fix. If two notches do not close the end, the canopy is likely too slack and needs new fabric.
Frequently asked questions
Which way do I turn the Presto Fix on a Fiamma F45s?
Clockwise, which Fiamma's manual also calls downwards. Use a flat screwdriver on the ring nut, with the awning fully unrolled. Turn one notch, close the awning, and check. Fiamma says one or two notches.
Where is the Presto Fix on a Fiamma awning?
On the end of the roller tube, at the end opposite the crank. You reach it with the awning fully unrolled. It is a round cap with a notched ring nut.
Why is one end of my Fiamma lead bar lower than the other?
Fiamma says the arm "may lower itself with wear and tear over time." Fix it at the upper bolt of the Dual Shock Absorber on the low side, with a 10 mm wrench. Check first that the bolts are not stuck in the upper slots.
Does the Fiamma ZIP have a Presto Fix?
Fiamma's F45s installation manual says "In Fiamma ZIP there is no Presto Fix." Older ZIP awnings may differ, so look for a notched cap on the roller end opposite the crank.
How do I know my Fiamma awning is fully closed?
Look at the red flags at each end of the lead bar. Fiamma says they are no longer visible when the awning is fully closed. A flag that still shows means that end is open.
Sources and further reading
- Fiamma SpA: F45s Maintenance and Repairs (2014; lead bar inclined, lead bar does not close properly, fabric and arm replacement). Second copy: PDF hosted by myGenerator
- Fiamma SpA: F45S installation instructions, arm adjustment and roller regulation cap Presto Fix (pages 29 to 33)
- Fiamma SpA: Fiamma Awnings Troubleshooting Guide (red flag, lead bar not closing on the side opposite the winch, Dual Shock Absorber), hosted by CamperLife
- Fiamma SpA: ZIP series installation instructions, page 29
- Fiamma SpA: 2014 catalog (Italian; awning feature table), hosted by CamperOnline
- Fiamma: F45s catalog pages (lengths, Presto Fix, Dual Shock Absorber), hosted by myGenerator
- T6 Forum: Fiamma F45s not going away fully (March 2024)
- MotorhomeFun: Fiamma F45s adjustment (August 2020)
- Class B Forum: Fiamma awning won't close properly (March 2009)
How we write our guides: figures are typical US ranges checked against manufacturer documentation, published standards and installer pricing. Read our editorial standards. Spotted an error or outdated detail? Request a correction.