Girard Awning Won't Retract
Quick answer
When a Girard GG750 awning will not retract, match the fix to where it stops. Silent means the 12V fuse or the awning main switch. Running 10 to 12 inches and stopping means low voltage at the motor. Stopping just short of a closed box with nothing binding means the IN limit, which Girard says moves about 1 inch for each quarter turn of the limit screw. An elbow that hangs down or a lead rail that rubs the case is an arm or rail adjustment. To close it now, the 13 mm manual override at the end opposite the motor turns one way only, closed. Run the motor no more than 4 minutes in any hour. Call Girard at 800-382-8442 if the manual's fixes fail.
When a Girard awning won't retract, where it stops tells you the fix. If nothing happens at all, check the 12V fuse and the awning main switch. If it runs 10 to 12 inches and stops, the motor is short of power. If it closes almost all the way and stops with a gap at the box, and nothing is rubbing, the motor's IN limit is set short. Girard's GG750 manual says "approximately ΒΌ turn of the adjustment screw represents about 1" of awning movement." If an arm elbow hangs down, or the front rail rubs the case, the arm or rail needs adjusting. To get it closed right now, use the manual override: a 13 mm wrench on a shaft at the end opposite the motor, which "can only close the awning."
Below are the terms, a fix for each symptom from Girard's own manual, the run time limit, re-pairing a remote, and when to call Girard. If your awning is not a Girard, start with RV awning won't retract. For how power RV awnings are put together, see RV awnings.
What a Girard GG750 is, and the words that matter here
Girard GG750. A box awning for RVs made by Girard Systems of San Clemente, California. Girard's manual calls the box a cassette, and when the awning is closed, the fabric, the roller tube and the folding arms all sit inside it. A power GG750 has a 12V DC motor hidden inside the roller tube. Because it is a box awning, "closed" means the box is shut tight, not just rolled up. For how box awnings differ from open-roller ones, see cassette awnings.
Lead rail. The long bar on the front edge of the fabric. It is held up by the arms when the awning is out, and when the awning closes, it pulls into the box and seals it. Girard sets it at "+/- 3 degrees" so it "rest[s] firmly into the cassette" and makes a weather seal for travel.
Elbow. The hinge in the middle of each folding arm. As the awning closes, each arm folds at its elbow and tucks into the box.
Limit switch. A stop built into the motor. It turns the motor off at a set point in each direction: the IN limit stops it when closing, and the OUT limit stops it when opening. On the GG750 you set them by turning two screws on the head of the motor. For how limits work on any awning motor, see awning motor limit adjustment.
Manual override. A shaft you turn by hand with a wrench to close the awning when the motor will not.
Duty limit. The most the motor may run before it needs a rest. Girard's warning is "do not exceed 4 minutes of operation per hour."
Girard awning won't retract: the fix by symptom
Every row here is a problem and fix from the troubleshooting guide in Girard's GG750 manual (rev 04122022), except the remote row, which comes from Girard's pairing steps.
| What you see | Likely cause | Girard's fix |
|---|---|---|
| Nothing happens at all | No 12V power reaching the awning | Check the panel fuse; turn on the Awnings Power Main Switch if your coach has one |
| Runs 10 to 12 in, then stops | Not enough power at the motor | Check for at least 12V DC at the motor; run the generator or plug in |
| Stops short of a closed box, nothing binding | IN limit set short, or fabric has stretched | Adjust the IN limit screw on the motor head |
| An elbow hangs down and stops the case closing | Elbow height or arm pitch off | Adjust elbow height and pitch at the arm shoulder |
| Lead rail rubs the side of the case | Lead rail shifted sideways | Loosen, tap the rail over with a rubber mallet, retighten |
| Motor end closes, far end does not | Lead rail out of adjustment | Adjust the lead rail; if that fails, call Girard |
| Wall switch works, remote does nothing | Remote not paired to the controller | Re-pair it using the steps for your controller |
It does nothing, or stops after 10 to 12 inches
Both of these are power problems, not a broken awning, and Girard's first fix for "motor will not operate" is to check the panel fuse on the 12V circuit. Its second is to make sure the Awnings Power Main Switch is on, if your coach has one.
If the motor runs "for 10-12" and then stop[s]," Girard says the motor "may not be receiving enough power." Check for at least 12V DC at the motor plug, and if it is lower, start the generator or plug into shore power, then try again. A house battery can read fine at rest and still drop too low once the motor pulls hard. For testing voltage under load, fuses and grounds, see RV awning motor problems.
It stops just short of closed: the IN limit
Girard's troubleshooting guide describes this one exactly. The motor stops "before the lead rail has closed completely" on one or both sides, and "there is no apparent binding." Girard's answer is that "the IN limit may need to be adjusted to allow the box to be closed tighter." The manual also warns that fabric stretches over time, and that this "will require an adjustment of the IN and/or OUT limit switch." So an awning that closed fine for years and now leaves a gap may only need a small turn.
How to set it, from the manual:
- Get the tool. Use the black plastic key that came with the awning, or a 4 mm (5/32 in) Allen wrench.
- Reach the motor. Open the awning a few feet. The limit screws are on the head of the motor.
- Find the IN screw. There are two screws, one for IN and one for OUT, with symbols printed next to them. The motor is marked + and - to show which way each screw moves the stop.
- Turn in small steps. About a quarter turn moves the stop about 1 inch, so turn, run the awning closed, and look at the box.
- Stop at the exact moment. The goal is a motor that shuts off "the exact moment the awning box closes."
Do not overshoot: Girard prints this in capitals. If the IN limit is set past the closed point, the motor keeps running against the shut box, and "this will destroy the motor." A small gap is a nuisance, but a motor that keeps pulling after the box is shut is a new motor.
The OUT limit is the other screw. Girard sets it so the fabric is taut and the arms stop "just before the arms lock," with "about a 1/4" gap at the elbow." If the fabric is loose at full extension, the roller is turning past that point, and the fix is the OUT limit. Leave the OUT screw alone if your only problem is closing.
An elbow hangs down or the rail rubs the case
If the motor runs but the box will not shut, look along the awning as it closes, because something is likely in the way.
Elbow hanging down. If an elbow sags and stops the case closing, Girard points to elbow height and pitch. Tools are a 17 mm and a 19 mm (3/4 in) open-end wrench and a 4 mm Allen wrench. For elbow height, open the awning about 12 inches. Screw C is the top bolt on the side of the arm's shoulder. Turn it clockwise with the 17 mm to raise the arm, then loosen screw D, the bottom bolt, with the 19 mm. To lower it, turn screw C counterclockwise, then tighten screw D. Close the awning fully and check that the arms fold into the box "without interference."
Arm pitch. Pitch is the tilt of the arm. Open the awning all the way. Screw A is a nut on the front of the shoulder. With the 17 mm, turn it clockwise to raise the pitch or counterclockwise to lower it. Girard warns against overtightening, and you may need to lift the arm a little to take the pressure off.
Lead rail angle. The rail's angle is set with a 4 mm Allen wrench in screw B. Clockwise increases the angle and counterclockwise decreases it. Girard says to set it "evenly on all of the arms."
Lead rail rubbing the side of the case. This means the rail has shifted sideways, and Girard's steps are:
- Open the awning about 3 feet.
- Loosen the lead rail's sideways adjustment screws on all arms.
- Take out the two fabric set screws at each end of the lead rail.
- Close the awning until the rail is about 4 inches from fully closed.
- Tap the end of the rail with a rubber mallet to move it into line.
- Tighten the adjustment screws, then put the fabric screws back.
If the motor end closes and the far end does not, Girard says to start with the lead rail adjustment and to call if that does not fix it. For arm and pitch basics on other brands, see RV awning adjustment.
It worked, then quit after a lot of use: the 4 minute rule
Girard's manual opens with this warning: "To prevent the motor from overheating do not exceed 4 minutes of operation per hour. Overheating will destroy the motor." That is 4 minutes of motor time in any hour, counting every trip out and in. The wired wall switch kit (98GC781B) also lists "maximum run time is 4 minutes."
Testing a limit, adjusting the arms, and running the awning in and out to check each step can use up 4 minutes fast. So keep track of how long the motor has run while you work. If it stops answering after a lot of runs, stop and give it the rest of the hour rather than pressing the switch again. Neither Girard document says what the motor does when it gets hot, so do not count on it to protect itself. For the general picture on hot awning motors, see awning motor overheating.
The remote does nothing: re-pair it
Girard's remotes and wall switches talk to the motor controller by radio. Girard calls this system G-Link, on 433.92 MHz. Each remote has to be paired to the controller, which Girard says is "usually done at the Girard Systems factory." If a wall switch still works but a remote does not, the remote may have lost its pairing.
Re-pairing depends on which controller you have. For the GC274B, Girard's controller for AC motor awnings, the steps are:
- Make sure the controller has power.
- Press and hold the MIDDLE and RIGHT buttons on the controller for about 5 seconds, until the green LED starts to flash.
- Press STOP. The green LED stops flashing and stays on.
- Press UP on the remote you are pairing. The green LED goes out.
Do each step within 10 seconds of the last one, or the controller "will revert to factory settings." The GC274B holds up to 20 remotes, and pairing a 21st replaces the most recent one. The GC274B can also be wired to close the awning when the ignition comes on or the parking brake is released. It then cuts power so the awning cannot go back out while the coach moves. So if your awning closes when you start the engine, that is the design. If it closes on its own when the engine is off, see RV awning retracts by itself.
The GG750 manual uses a different controller and a different motion sensor. It covers re-pairing the sensor, but not the remote. If your controller is not a GC274B, get its manual or call Girard rather than pressing buttons on a guess.
Getting it closed now: the 13 mm override
If you need to move and the motor will not close the awning, use the override. From the GG750 manual:
- Go to the end of the box opposite the motor. The manual's figure shows a right-hand motor, so on a left-hand awning the override is on the other side.
- Take off the end cap by removing its 3 Phillips screws.
- Put a 13 mm wrench on the override shaft and turn it to close the awning.
The override is "one-way, it can only close the awning." Once it is in, you cannot open it by hand to fix the fault, so plan any repairs that need the awning open, like the limit or arm adjustments, before you crank it shut. Then check that the box is closed all the way along. Girard says every awning must be closed before the vehicle moves, with a visual check that each one is fully closed. If an awning has already opened on the road, see RV awning opened while driving.
Worked example: a gap at the box after a few seasons
Take a GG750 on a motorhome that has closed fine for three years. Suppose it now stops with about a 1 inch gap between the lead rail and the box on both ends. Nothing is rubbing, and both elbows fold in cleanly.
Step 1: read the symptom. Both ends stop short and nothing binds. That is the manual's IN limit case. Girard also says fabric stretches over time, which fits an awning that used to close.
Step 2: size the turn. A 1 inch gap at about 1 inch per quarter turn means a quarter turn of the IN screw. Start there, not with a half turn. Overshooting is the one mistake here that can ruin the motor.
Step 3: set it. Open the awning a few feet, find the IN screw by its printed symbol, and turn it a quarter turn one way. Close the awning and watch the box. If the gap got bigger, the turn went the wrong way, so turn it back a half turn.
Step 4: watch the clock. Each test run counts toward the 4 minutes per hour. If the box is not right after a few tries, stop and finish later.
Step 5: stop at the right point. The setting is right when the motor shuts off the moment the box closes. If it still runs after the box is shut, back the screw off at once.
An older Girard: the current limit module
Not every Girard awning is a GG750. On the Beaver owners forum, an owner of a 2004 Beaver Patriot Thunder wrote that his awning "would extend and not retract." It stopped even with no fabric on the roller. His finding was that "the current limit device was most likely bad," and that "apparently they stopped using modules." He bypassed the module and wired the motor straight in, and he stressed that the closing limit then had to be set so "the motor turns off at the exact moment the awning cover closes," or "a burned out motor results." That matches Girard's own warning for the GG750.
This is one owner's report on one older coach, not a Girard procedure, and bypassing a module means working on the coach's wiring, and the GC274B controller runs on 110V AC. Ask Girard before you cut anything out.
When to call Girard
Girard's toll-free line is 800-382-8442, and the service line in the GG750 manual is 949-259-4000. The GC274B guide gives hours of 7:30am to 3:30pm Pacific for help with G-Link programming. The GG750 manual says to call when:
- The motor will not run, and the fuse and main switch are fine.
- It still stops at 10 to 12 inches with at least 12V at the motor.
- The motor end closes and the far end does not, after the lead rail adjustment.
Call too if an arm's elbow is broken or the motor needs replacing. Girard says there are "no repairable parts inside of the arm," so a broken elbow means a new arm. When a new motor goes in, the manual says to test it only a little each way at first, because its limits are not set yet. Then the limits must be adjusted.
What this answer does not cover
The steps here come from Girard's GG750 manual and its GC274B pairing guide. They fit the GG750 box awning with a 12V DC motor. Other Girard awnings, older coaches with separate current limit modules, and awnings on 110V AC motors may use different parts, screws and steps, so get the manual for your model. The GG750 manual does not say which of the + and - marks closes the IN stop tighter, so test a small turn and watch the result. It also does not say the motor has a heat cutout, so treat the 4 minute rule as the only protection you can count on. If an awning was opened in strong wind, the arms, rail or brackets may be bent, and no limit setting fixes that. A coach under warranty should go to the dealer or Girard before you adjust anything.
Key takeaways
- Silent: check the 12V fuse and the Awnings Power Main Switch. Stops after 10 to 12 inches: get at least 12V to the motor.
- Stops just short of a closed box with nothing binding: adjust the IN limit, about 1 inch per quarter turn of the screw.
- Set the IN limit to stop the moment the box closes. Overshooting it destroys the motor.
- An elbow hanging down or a rail rubbing the case is an arm or lead rail adjustment, not a motor fault.
- The 13 mm override at the end opposite the motor only closes. Run the motor no more than 4 minutes an hour, and call Girard at 800-382-8442 if the manual's fixes fail.
Frequently asked questions
How do I manually retract a Girard awning?
On a GG750, take the end cap off the end opposite the motor by removing its 3 Phillips screws. Turn the override shaft with a 13 mm wrench to close the awning. The override only closes. It cannot open the awning again.
Why does my Girard awning stop before it closes?
If nothing is binding, the motor's IN limit is stopping it short. Girard says fabric stretches over time, so the limit may need a small turn. About a quarter turn of the screw moves the stop about 1 inch. Set it to stop the exact moment the box closes.
Where are the limit screws on a Girard awning motor?
On the head of the motor. Open the awning a few feet to reach them. Use the black key that came with the awning or a 4 mm (5/32 in) Allen wrench, and follow the printed symbols.
How long can a Girard awning motor run?
Girard says not to run it more than 4 minutes in any hour, because "overheating will destroy the motor." That counts every run, both out and in.
What is Girard's phone number for awning help?
Girard's toll-free number is 800-382-8442. The GG750 manual also lists a service line at 949-259-4000.
Sources and further reading
- Girard Systems: GG750 Awning Installation, Service and Repair Manual, rev 04122022 (hosted by Oliver Travel Trailers)
- Tiffin Motorhomes knowledge base: Girard GG750 Awning: Installation and Service Manual (second copy of the same manual)
- Girard Systems: AC Motor Control Module GC274B, Installation and Pairing Instructions, rev 12302015 (hosted by Forest River)
- Beaver Ambassador Club forum: Girard Awning Won't Retract: Solved the Mystery (July 2017)
How we write our guides: figures are typical US ranges checked against manufacturer documentation, published standards and installer pricing. Read our editorial standards. Spotted an error or outdated detail? Request a correction.