RV Awnings

Lippert Solera Awning Won't Retract

Quick answer

When a Lippert Solera power awning won't retract, match the fix to what it does. Silent means power: a battery that is not fully charged, the fuse, a tripped breaker, or a hot motor whose thermal breaker resets once it cools. On a Smart Arm, the touch pad has to be switched on first. Slow, or stopping part way, usually means low voltage, so plug in and check for at least 12 volts at the motor. Moisture faults on a Smart Arm lock out extend, not retract. If it rolled up backward, press RETRACT and it unrolls the right way. To close it by hand, pull the rubber grommet on the drive head, which three of the four manuals put on the right end as seen from outside. Then run a 7/16 in socket on a drill counterclockwise. If the motor is dead, strap the outer arm to the mount arm before you let go of the nut. Lippert's line is (574) 537-8900, or 432-LIPPERT on the 2025 manuals.

When a Lippert Solera power awning won't retract, what it does when you press the switch tells you where to look. If it does nothing, it has no power. Check the battery, the fuse and the breaker, and give a hot motor time to cool, because its thermal breaker resets by itself. If it moves slowly or stops part way, the motor is short of voltage, so plug in and check for at least 12 volts at the motor. If it rolled up with the fabric under the tube, press RETRACT and it will unroll the right way. To get it closed right now, use the manual override. Pull the rubber grommet on the drive head, put a 7/16 in socket on a drill, and spin the nut counterclockwise.

Below are the terms, a table of what you see and what to do, each fix in turn, the override for each Solera model, a worked example and when to call Lippert. If your awning is not a Solera, start with RV awning won't retract.

What a Solera power awning is, and the words that matter here

Lippert Solera. A line of patio awnings for RVs made by Lippert (LCI). The power models have an electric motor inside the roll tube, the long tube the fabric winds onto, and it runs off the RV's battery. Lippert's manuals cover the Solera Power Awning, the Smart Arm, the 2000 Series and the 3000OG Solar, which has a solar panel built into the fabric. For how power RV awnings work in general, see RV awnings.

Drive head. The end of the awning that holds the motor. The other end is the idler head, which has no motor.

Manual override nut. A 7/16 in nut on the motor, hidden behind a rubber grommet in the drive head. Turning it with a socket winds the awning in or out with no power.

Outer arm and mount arm. Each support arm has two parts. The mount arm is fixed to the side of the RV, and the outer arm swings out with the roll tube. Lippert counts a Smart Arm awning as closed "as long as the outer arm is overlapping the mount arm."

Thermal breaker. A heat cutout inside the motor. It shuts the motor off when it gets too hot, and Lippert says it "auto resets once cooled."

Smart Arm touch pad. On the Smart Arm model, a set of buttons built into the awning arm, so you can work the awning from outside. It has to be switched on before it does anything.

Lippert Solera won't retract: what you see and what to do

Each row is a ruling from the sections below, with its source named there.

Solera power awning won't retract: likely cause and fix
What you seeLikely causeWhat to do
Nothing at allNo power, travel lock on, or a hot motorCheck travel locks, fuse, breaker and battery; let the motor cool
Smart Arm touch pad does nothingTouch pad not switched onHold the lock button 3 seconds until the green light comes on
Slow, or stops part wayLow voltage at the motorPlug in or run the generator; check for at least 12 V at the motor
At least 12 V at the motor, still nothingMotor has likely failedClose it with the override; replace the motor
Fuse blows the moment it goes inShort in the wiringInspect the wiring; do not keep fitting fuses
Fuse blows partway through closingSomething binding, such as a bent armClose it by hand and feel for where it sticks
Stops with outer arm over mount armNothing wrongLippert counts that as closed
Smart Arm touch pad lock light blinkingMoisture fault or low voltageRetract still works; on a touch pad fault, use the inside switch
Switch runs it the wrong wayWires reversedReverse the wires
Rolled up with fabric under the tubeExtend held too long, or pressed by mistakePress RETRACT; it unrolls to the right side

It does nothing at all

Lippert's Smart Arm manual lists four checks for "Awning won't open or close." First, if your RV has travel locks on the arms, make sure they are unlocked. Second, check that the fuse is good. Third, the motor may have overheated and tripped its thermal breaker, which "auto resets once cooled." So if you have just run it in and out a few times, wait and try again. Fourth, check for power at the motor while someone holds the switch.

On a Smart Arm, there is one more step before any of that. The touch pad starts out off. Press and hold the lock button for three seconds, and a green light shows it is on. Only then do the arrows work.

A good fuse does not mean the circuit has power. On a Heartland Sundance owner's thread, a forum member pointed out that near the battery there is often a row of 12 volt breakers under a red rubber boot. One of them is a manual reset type with "a teeny tiny reset button." If that one has tripped, the awning has no feed even though every fuse looks fine. For tracing power from the battery to the switch, see RV awning motor problems.

It is slow, or stops part way

Every Solera manual starts both extend and retract with the same step: make sure the battery is "fully charged and connected." A tired battery can run a light and still fail to turn a motor. An etrailer expert answering a 2020 Solera owner put the number on it: battery voltage "should be at least 12 volts." The next test is at the motor's power wire. If that reads at least 12 volts and the awning still will not move, the expert said, "it's likely the motor that needs replaced."

The easy fix is more voltage. Plug into shore power or run the generator. On the Heartland thread, the same forum member said 12.5 volts "is a battery only reading," and that on shore power you "should have seen 13.2 - 13.6V coming off the converter." The owner had found 13.2 volts at the motor while extending but only "around 12 or so" when retracting. Closing works the motor harder, so a weak supply shows up there first.

The Smart Arm has a warning built in. If voltage drops below 11 volts, the awning light starts flashing when it is on. A flashing light on a Smart Arm is a battery clue, not a bulb fault. For lights that will not come on at all, see RV awning LED lights not working.

The fuse blows every time

When a fuse keeps blowing, the timing tells you which kind of fault you have. An etrailer expert put it this way. If the fuse blows "almost immediately" when a new one goes in, "there is likely a short in the wiring." If it blows "while in the process of retracting," then "it is likely a mechanical error." The motor is pulling extra current to fight something, such as a bent arm. The expert's advice was to close the awning by hand with the override and feel for the spot where it sticks.

Do not keep putting in fuses, and never fit a bigger one. A fuse that blows is doing its job. If you think an arm is bent, see RV awning adjustment for what the arms should look like.

It stops, but looks a little open

Look at the arms before you call it a fault. Lippert's Smart Arm table says the awning "is considered completely closed as long as the outer arm is overlapping the mount arm," and adds that "this overlap can vary." So a little gap that varies from one awning to the next can be normal.

If the arms do not overlap, the same table gives two causes. The motor may have hit its thermal breaker, so let it cool. Or the fabric may not be square to the RV and rolling straight on the tube. Fabric that creeps toward one end makes a fat roll on that side, and the awning stops early. For why fabric drifts, see awning retracts unevenly.

It got wet, and the Smart Arm light is blinking

This is where a lot of owners guess wrong. They assume water has locked the awning out, but Lippert's own fault rules say it should still close. The Smart Arm checks for moisture on assemblies built after May 2018, and it has two levels of fault.

Level 1: water in the main 12-pin connector. The inside extend switch and the inside light control lock out. Lippert's manual says in bold, "There will be NO lock-out of the retract function." The touch pad's lock light blinks nonstop, the same as a low voltage fault. The outside touch pad keeps working. Once no fault has been seen for 100 seconds, pressing any touch pad button clears it, and so does turning the Smart Arm controller off and on.

Level 2: water in the touch pad or the controller board. The touch pad's extend and light buttons lock out, but the inside switches still work. A power cycle will not clear it. To get limited use of the touch pad back, press extend, then retract, then light, then wind, and then hold the unlock button for 10 seconds.

So when the outside pad seems dead after rain, try the inside switch. One catch: on RVs with OneControl, Lippert says OneControl is not locked out, "however water in the connector can prevent operation." If water is detected while the awning is going out, the controller stops it and closes it on its own. That can look like a fault, but it is the design. If your awning closed by itself in wind, see RV awning retracts by itself.

It rolled up backward, or runs the wrong way

The fabric should always sit on top of the roll tube. All four manuals say the same thing about what happens when it does not. If extend is held too long, or pressed by mistake instead of retract, "the awning will roll up backward. This is not a defect." The fix is to press RETRACT. The awning then unrolls the other way, extends with the fabric on top, and works normally after that. Do not keep pressing extend to "finish" closing it, since that is what wound it the wrong way.

A different problem looks similar. If the switch's extend button closes the awning and its retract button opens it, the Smart Arm table says the wires to the awning "have been reversed or switched." The fix is to reverse the wires. Look at the roll before you do: if the fabric comes off the bottom of the tube, it is a backward roll, not the wiring. How to tell the two apart, and where to stop when you extend, is in RV awning rolled up backwards.

Getting it closed now: the manual override

Every Solera power manual has the same core steps for closing the awning by hand, "in the event of power loss or motor failure":

  1. Find the drive head. Three of the four manuals say it "is always located on the right side of the awning as it is viewed from outside." The Smart Arm manual does not say which side, so look for the end with the grommet.
  2. Pull the rubber grommet out of the drive head. Behind it is the override nut on the motor.
  3. Put a 7/16 in socket on a cordless drill and spin the nut counterclockwise to retract. A step stool or ladder may be needed to reach the end.
  4. Stop when it is fully in, take off the socket, and push the grommet back in.

A ratchet works too, but the Power Awning and 2000 Series manuals warn it "will take a significant amount of time." The Heartland owner said the nut will "SLOWLY retract or extend the awning." So bring a drill if you can. Lippert's steps do not say to cut power first. Even so, keep anyone away from the switch while the socket is on the nut.

Solera manual override by model, from each owner's manual
Model and manualDrive head sideTo retractTo extendStrap a dead motor?
Solera Power Awning, CCD-0001369 rev 02.26.20Right, from outsideCounterclockwiseNot statedYes
Solera Smart Arm, CCD-0001359 rev 02.19.20Not statedCounterclockwiseNot statedYes
Solera 2000 Series, CCD-0002686 rev 01.28.25Right, from outsideCounterclockwiseNot statedYes
Solera 3000OG Solar, CCD-0007873 rev 02.27.25Right, from outsideCounterclockwiseClockwiseNot in this manual

The direction to close is the same on every model: counterclockwise. The 3000OG manual is the only one that also prints the direction to open, which is clockwise. The other three say the override can extend the awning but give only the retract direction.

Strap it before you let go if the motor is dead. Three of Lippert's manuals say the motor's internal drive is what stops the awning moving on its own. If the motor is "damaged or disabled," secure the awning closed "with a strap around both the outer support arm and the mounted support arm before the manual override nut is released." The 3000OG manual leaves this step out. A strap costs nothing, so use one on any Solera with a dead motor.

That same line settles a common mix-up. A 2025 etrailer answer to a Solera owner blamed a torsion spring "wound 14 times at install." That is how spring-loaded manual awnings work. None of the four Solera power manuals mentions a spring, and three say the motor holds the awning. So on a Solera power awning, look at power and the motor first. For overrides on other awnings, see awning manual override, and for the Girard version, see Girard awning won't retract.

Worked example: dead at the campsite, leaving tomorrow

Take a 2000 Series awning on a travel trailer after four days of dry camping. Suppose you press RETRACT and nothing happens: no hum, no click.

Step 1: rule out the easy things. There are no travel locks on the arms. The fuse is good, and the reset button on the breaker near the battery is not popped.

Step 2: check voltage. Say the battery reads 11.8 volts. That is under the 12 volts the etrailer expert gives, so start the generator. A converter on shore power should give about 13.2 to 13.6 volts. Try again.

Step 3: read the result. If it now closes, the battery was the cause, and nothing is broken. If it still does nothing, check the motor's power wire while someone holds RETRACT. At least 12 volts there with no movement points to the motor.

Step 4: close it by hand. Stand outside facing the trailer and go to the right end. Pull the grommet, fit a 7/16 in socket on a drill, and run it counterclockwise until the awning is in.

Step 5: strap it. In this case the motor looks dead, so wrap a strap around the outer arm and the mount arm on each side before you take the socket off. Then push the grommet back in, and book the motor repair before the next trip.

When the motor has failed

If the motor gets at least 12 volts and does not turn, it needs replacing. The etrailer expert named two Lippert replacement motors by age: part LC266149 for Solera power awnings from 2015 or before, and LC373566 for later ones. Check your awning's details before you order, since the right part depends on the model.

One Heartland owner went another way. He found the motor was "nothing more than a power window motor with the manual overide." He swapped in a $30 aftermarket window motor and noted, "It wont have a manual overide." That is one owner's choice on a 2017 thread, not a fix Lippert offers. If you go that way, you give up the only way to close the awning with no power.

When to call Lippert

Lippert's line in the 2020 manuals is (574) 537-8900. The 2025 manuals list 432-LIPPERT (432-547-7378). The email in all four is customerservice@lci1.com. Call when:

  • The motor gets at least 12 volts and does not turn.
  • The fuse blows again and you cannot find a short or a bent arm.
  • A Smart Arm fault will not clear with the steps above.
  • The override nut turns but the roll tube does not.

What this answer does not cover

The steps here come from four Lippert owner's manuals for the Solera power models. They do not cover manual Solera awnings with a pull strap and spring, the Solera slide topper, or awnings from other makers, which close in different ways. The manuals do not give amp ratings for the awning fuse or the thermal breaker's cool-down time, so this page gives neither. The 12 volt figure and the converter range come from an etrailer expert and a forum member, not from Lippert. If an arm is bent from wind, or the awning was hit, closing it by hand may not be safe, so get a technician to look first. Never drive with the awning out or loose. If yours opened on the road, see RV awning opened while driving. An RV still under warranty should go to the dealer or Lippert before you swap any parts.

Key takeaways

  • Silent: check travel locks, fuse, the reset breaker near the battery, and let a hot motor cool. On a Smart Arm, hold the lock button 3 seconds first.
  • Slow or stopping: plug in. Look for at least 12 volts at the motor. At least 12 volts with no movement likely means the motor.
  • Smart Arm moisture faults lock out extend, not retract. Try the inside switch if the outside pad is locked.
  • Rolled up backward is not a defect. Press RETRACT and it unrolls the right way.
  • Override: right end, pull the grommet, 7/16 in socket on a drill, counterclockwise to close on every model. Strap the outer and mount arms first if the motor is dead.

Frequently asked questions

How do I manually retract a Lippert Solera awning?

Pull the rubber grommet out of the drive head. Lippert puts it on the right end as you face the RV, on every model whose manual says. Put a 7/16 in socket on a cordless drill and spin the override nut counterclockwise until the awning is in. Then put the grommet back. If the motor is dead, strap the outer and mount arms together before you take the socket off.

Which way do you turn a Solera awning override?

Counterclockwise to retract, on every Solera power model. The 3000OG Solar manual also says clockwise to extend. The other manuals give only the retract direction.

Why does my Solera awning roll up backward?

Extend was held too long or pressed by mistake, so the fabric wound under the tube. Lippert says this is not a defect. Press RETRACT, and the awning unrolls to the right side and works normally again.

Does a Lippert Solera power awning have a spring?

None of the four Solera power manuals mentions one. Three of them say the motor's internal drive holds the awning in place. That is why Lippert says to strap the arms if the motor is dead.

What voltage does a Solera awning motor need?

Lippert says only that the battery should be fully charged and connected. An etrailer expert gives at least 12 volts at the battery and at the motor. On shore power, a converter should give about 13.2 to 13.6 volts.

What is Lippert's phone number for awning help?

The 2020 Solera manuals list (574) 537-8900. The 2025 manuals list 432-LIPPERT (432-547-7378).

Sources and further reading

How we write our guides: figures are typical US ranges checked against manufacturer documentation, published standards and installer pricing. Read our editorial standards. Spotted an error or outdated detail? Request a correction.