RV Awning Rolled Up Backwards
Quick answer
An RV power awning rolls up backwards when EXTEND is held past full extension, or pressed by mistake instead of RETRACT. The motor keeps turning the tube the same way, so the fabric winds back on from underneath. Lippert says this "is not a defect." The fix is to press and hold RETRACT. The awning rolls back out, and Lippert says it "will then extend to its correct orientation." Do not press EXTEND again, because that is the direction that caused it. It happens on power awnings with no stop at full extension, such as the Lippert Solera. Owners say spring-loaded power awnings, such as Dometic's, stall instead. If the switch seems reversed, look at the roll first: fabric leaving the bottom means a backward roll, not crossed wires. Stop extending when the valance seam shows and a strip of roll tube is bare.
An RV power awning rolls up backwards when EXTEND is held too long, or pressed by mistake instead of RETRACT. The fix is to press and hold RETRACT. Lippert, maker of the Solera power awnings, says a backward roll "is not a defect." Pressing RETRACT, its manuals say, makes the awning "extend to its correct orientation," and then it works as normal. Do not press EXTEND to fix it, because EXTEND is the button that wound it the wrong way.
Below are the terms, how to tell a backward roll from crossed switch wires, which awnings can do it, the forum advice to skip, why a backward roll holds water, and where to stop when you open the awning.
What "rolled up backwards" means, and the words that matter here
Rolled up backwards. The fabric has wound onto the roll tube from underneath instead of over the top. Lippert's rule is plain: "The awning fabric should always be above the roll tube." On a closed awning that is rolled backwards, the underside of the fabric faces out. One Forest River owner put it this way: the "bottom (white side) rolled to the outside opposed to the roof (brown side)." Owners also call it rolled inside out or over wound.
Roll tube. The long tube at the front edge of the awning that the fabric winds onto. On a power awning, a 12 volt motor inside or at the end of the tube turns it. The other edge of the fabric is fixed in a rail on the side of the RV.
Power awning. An RV patio awning that a motor opens and closes from a switch. A manual awning uses a spring in the tube and a pull strap instead. For how the two differ, see power vs manual RV awnings.
Valance. The short flap of fabric that hangs down from the front of the awning. The seam where it joins the main fabric is the valance seam. Lippert uses it to mark full extension.
Why it happens: the motor has no stop at full out
When you hold EXTEND, the motor turns the tube to unwind the fabric. On some power awnings, including the Lippert Solera, nothing tells the motor to stop when the fabric runs out. So the tube keeps turning the same way, and the fabric starts to wind back on from underneath. The awning then pulls itself back toward the RV, even though you are still holding EXTEND.
Owners describe it the same way. "There is no 'hard stop' on an electric awning," one Forest River member wrote. If you keep your finger on the button, "the motor keeps spinning," and the awning rolls "back up inside out." Another put it in one line: "The only way to roll it inside out is to continue turning the drum in the direction it turns when opening." On a Jayco forum, an owner watched a dealer's salesperson do it on a KZ fifth wheel. "If you hold the switch long enough it will roll all the way out and then start rolling back in," they wrote.
Lippert's manuals give two ways in. Extend is "engaged too long," or extend is "hit inadvertently instead of retract." The second one is easy to do. The awning is half out, you mean to close it, and your thumb lands on the wrong arrow. A third way shows up in one 2026 thread. The owner's guess was that a service tech ran the awning all the way out during an inspection, and nobody noticed until the next trip.
How to fix it: press and hold RETRACT
All three Lippert Solera manuals checked for this page give the same fix. Press RETRACT. The Smart Arm troubleshooting table says to "simply operate the awning in the retract direction." Here is what you will see:
- Look at the roll first. Check that the fabric leaves the tube from the bottom. If it leaves from the top, the roll is fine, and your problem is something else.
- Press and hold RETRACT. On a backward roll, RETRACT turns the tube the way that unwinds it. So the awning moves out, away from the RV. That looks wrong, but it is not.
- Keep holding. The fabric unwinds from under the tube until it is fully out. Lippert says the awning "will then extend to its correct orientation." The Forest River owner who fixed theirs said, "I rolled it out and held the button down and it retracted it's self correctly." Another member gave the same advice: hold the button "all the way out and back in."
- Check the roll again. Once it is closed, the fabric should come off the top of the tube. From then on, EXTEND opens it and RETRACT closes it, as labeled.
On a Smart Arm, the touch pad must be switched on first. Hold the lock button for three seconds until the green light comes on. Lippert's own blog gives the same fix, in almost the same words, as the manuals.
If the awning will not move at all, the roll is not the problem. Start with RV awning won't retract, or for a Solera, Lippert Solera awning won't retract.
The forum fixes that are wrong
"Just hit extend and keep holding it." This was posted as the fix in a 2016 Forest River thread. It is the opposite of what Lippert says. Lippert names holding extend as the cause, and gives RETRACT as the cure. Pressing EXTEND on a backward roll keeps the tube turning the way that wound it under. An earlier reply in the same thread said to "Run it out again and it will reverse itself." The owner tried, and wrote back that "it continues to retract white out." What finally worked was holding one button through the whole trip, out and back in.
Rewiring the switch. A backward roll makes the switch seem reversed. Press RETRACT and the awning goes out. Press EXTEND and it comes in. A 2026 Forest River owner with a Solera on a Clipper 17FQ was ready to swap the wires behind the switch. Another member stopped them: the switch "was probably held too long in the extend position and it rewound backwards, giving the effect of a reversed switch." The owner checked, and the fabric was indeed over wound. Swap the wires on a backward roll and you end up with two faults, because once the fabric is righted, the switch really will run backwards.
"It can't roll backwards without a broken spring." That is true of some awnings and false for others. See the next section.
"Backwards keeps water out." One Jayco forum member had read that a backward roll is "suppose to help keep water from collecting." Lippert says the opposite: the fabric "should always be above the roll tube." The water section below gives the reason.
The other cause: switch wires reversed
Lippert's Smart Arm troubleshooting table lists two separate problems that look alike:
- "Awning works in the opposite direction of what switch shows." Cause: "Wires going to awning have been reversed or switched." Fix: "Reverse the wires."
- "Awning rolls up backward." Fix: run it in the retract direction, as above.
The test that tells them apart is where the fabric leaves the roll. The member in the Clipper thread said to check "is it coming off at the top (normal) of the roll or bottom (over wound)." Fabric off the bottom means a backward roll, so fix the roll and leave the wires alone. Fabric off the top, with EXTEND still closing the awning, points to the wiring. In that thread, the awning end had a plug that could not go in the wrong way. So the owner looked at the push-on connectors behind the switch, but the roll turned out to be the cause. For tracing 12 volt wiring, see RV awning motor problems and awning wall switch problems.
Which awnings can roll up backwards
Power awnings with nothing to stop the motor at full extension. The Lippert Solera is the clear case. All three Solera manuals warn about it. Their manuals say the motor's own drive holds the awning in place, and none of them mentions a spring. Owners on Forest River and Jayco forums report the same thing on their power awnings, and one watched it happen on a KZ fifth wheel.
Not, by owner reports, spring-loaded power awnings. Some power awnings, such as the Dometic 9100, also have a spring inside the tube that pulls toward closed. A Forest River member with a spring-loaded power awning said, "mine will NOT roll backwards even if I hold the button, I've tried and the motor just stalls out." They added that "the motor cannot overcome the torsion spring." Another member said a Dometic/A&E awning "will not do that due to a torsion spring." So if yours stalls at full out, let go of the switch, because it is not rolling under. These are owner reports, not maker statements, but they fit how the two designs work.
Not awnings whose motor has an OUT limit. A limit switch cuts the motor at a set point when opening. Girard's GG750, for example, has IN and OUT limits, covered in Girard awning won't retract. For how limits work on any awning motor, see awning motor limit adjustment.
Not manual awnings. A Forest River member put it simply: "With a manual awning I would agree there is no way for it to roll up backwards." You pull it out by hand, and the spring winds it back in.
Why a backward roll holds water
Owners say a correct roll is smooth on top, and a backward roll is not. A Jayco forum member gave the hand test: "Stand in doorway and feel the fabric when rolled up. If smooth over the top OK. Reversed and you'll feel the space where water can get in the roll." They added, "They wick enough water without this drainage."
Even rolled the right way, power awnings take in some water. In a 2016 Forest River thread, owners described water "raining" out of the roll on opening. Some blamed water wicking in at the ends, and others blamed condensation. A backward roll adds a gap on top to that.
Water in the roll matters because of mildew. Lippert says that if the awning goes in wet, you should extend it "and let it dry as soon as conditions allow." Mildew, its manuals add, grows "on the accumulated dust, dirt and grime," not on the fabric itself. For cleaning it off, see awning mold and mildew.
When the awning is open, the fabric should also sit on top of the tube. Lippert's blog warns that if water pools on the fabric, it "will begin to stretch and sag." Its manuals say to set the pitch arm to tip one side down so water runs off. For more on pooling, see water pooling on an awning.
Where to stop when you extend it
The way to prevent a backward roll is to let go of EXTEND at the right moment. Lippert gives the mark for each model:
- Solera Power Awning (CCD-0001369): extension "is considered complete when the fabric is completely unrolled, the valance seam is visible and a section of the roll tube is exposed."
- Solera 2000 Series (CCD-0002686): complete when "the valance is hanging down from the roll tube" and the fabric's single polycord shows "between the 9 and 12 o'clock positions as viewed from the end of the drive head." The polycord is a cord sewn along the edge of the fabric, and the drive head is the motor end.
- Solera Smart Arm (CCD-0001359): the manual says to hold extend "until the awning is extended completely." It also has a "One Touch" extend: press the extend arrow twice within two seconds. That only works with the optional wind sensor installed.
Owners use the same marks. One said to extend "only until the flap hangs straight vertical down from the roller," and to leave "a small portion of the awning fabric over the top edge of the roller." Another owner said theirs gives a click when the flap is down, and that is when they let go. If you are unsure, stop a little short. One owner whose awning rolled backward the first time ran it out "just shy of fully" the next day, "and it rolled correctly."
| What you see | What it means | What to do |
|---|---|---|
| Closed awning shows the underside; fabric leaves the bottom of the tube | Rolled backward (Lippert: "not a defect") | Press and hold RETRACT until it goes out and back in |
| Holding EXTEND, the awning starts coming back in | Past full extension, winding on from underneath | Let go; press and hold RETRACT |
| Switch seems reversed; fabric leaves the bottom of the tube | Backward roll, not wiring | Fix the roll with RETRACT; do not touch the wires |
| Switch runs it the wrong way; fabric leaves the top of the tube | Wires reversed (Smart Arm table) | Reverse the wires |
| Spring-loaded power awning stalls at full out | The tube spring stops it winding under (owner reports) | Let go of the switch; it has not rolled backward |
Worked example: back from service, and the switch seems reversed
Take a travel trailer with a Lippert Solera Power Awning, just back from a dealer inspection. Suppose that at the campsite you press EXTEND and the awning stays shut. You press RETRACT and it starts to move out.
Step 1: do not reach for the switch wires. Stand at the end of the awning and look at the roll. Say the fabric leaves the tube from the bottom. That is a backward roll, and it is enough to explain the "reversed" switch.
Step 2: press and hold RETRACT. The awning moves out as the fabric unwinds from under the tube. Keep holding past full out. By Lippert's manual, it should then go to the right orientation. By owner reports, it then rolls back in with the fabric over the top.
Step 3: check it. The roll should now be smooth on top, with the fabric leaving from the top. Press EXTEND. Let go when the valance seam is visible and a strip of roll tube is bare. Then set the pitch so one side is lower for rain.
Step 4: read the result. If EXTEND opened it and RETRACT closes it, nothing was ever wrong but the roll. If the fabric was on top and EXTEND still closed it, that is the Smart Arm table's other row: reversed wires.
What this answer does not cover
The fix and the stop marks come from three Lippert Solera manuals and Lippert's blog. Other makers' manuals were not checked for this page. The claims about spring-loaded and limit-stop awnings come from owner reports and our brand guides, not from a maker's statement about backward rolls. Lippert does not say how far the awning can over-run before something is strained, so do not test it. If the arms or tube look bent, or the motor labors or stops partway, stop and treat it as a fault. Never travel with the awning loose or partly out, and see RV awning care and wind safety before you open it in wind. If your RV is under warranty, ask the dealer or Lippert before you touch the wiring.
Key takeaways
- Holding EXTEND past full out, or pressing it by mistake, winds the fabric on from underneath. Lippert says that is "not a defect."
- The fix is to press and hold RETRACT. The awning goes out, then comes back in the right way. Do not press EXTEND to fix it.
- A switch that seems reversed is often a backward roll. Look at the roll before you touch the wires: fabric off the bottom means a backward roll.
- Lippert Solera and other power awnings with no stop at full out can do this. Owners say spring-loaded ones, such as Dometic's, stall instead.
- Stop extending when the valance seam shows and a section of roll tube is bare. A backward roll leaves a gap on top where water gets in.
Frequently asked questions
How do I fix an RV awning that rolled up backwards?
Press and hold RETRACT. The awning will roll out as the fabric unwinds from under the tube. Keep holding, and it goes to the right orientation and works normally after that. Lippert gives this fix in its Solera manuals.
Is it bad if my RV awning rolled up backwards?
Lippert says it "is not a defect," so nothing is broken. Fix it before you travel, though. Owners say a backward roll leaves a gap on top where rain gets into the roll, and Lippert says the fabric should always be above the roll tube.
Why does my awning go out when I press retract?
Most likely it is rolled up backwards. Look at the end of the roll. If the fabric leaves the tube from the bottom, keep holding RETRACT until it goes out and back in. If the fabric leaves from the top, the switch wires may be reversed.
Which way should RV awning fabric roll?
Over the top of the roll tube. Lippert's manuals say the fabric "should always be above the roll tube." When the awning is closed, the top side of the fabric faces out.
Can a Dometic power awning roll up backwards?
Owners of spring-loaded Dometic power awnings say no. One said the motor "just stalls out" because it cannot overcome the torsion spring. That is an owner report, not a Dometic statement.
How far should I extend a power RV awning?
On a Solera Power Awning, until the fabric is fully unrolled, the valance seam is visible and a section of the roll tube is exposed. On a Solera 2000 Series, until the valance hangs down and the polycord shows between 9 and 12 o'clock from the motor end.
Sources and further reading
- Lippert: Solera Power Awning Owner's Manual, CCD-0001369 rev 02.26.20 (backward roll note, extension complete at valance seam; hosted by Forest River)
- Lippert: Solera Smart Arm Owner's Manual, CCD-0001359 rev 02.19.20 (troubleshooting table: reversed wires and backward roll; hosted by Forest River)
- Lippert: Solera 2000 Series Awning Owner's Manual, CCD-0002686 rev 01.28.25 (polycord between 9 and 12 o'clock)
- Lippert: RV Awning Operation Guide (blog; backward roll and pooling)
- Forest River Forums: Awing retraction (May and June 2016; Solera owner, the extend advice, the fix that worked)
- Forest River Forums: Power awning rolled up under-side out (April 2015; no hard stop, torsion spring debate, "just shy of fully")
- Forest River Forums: Solera Awning Switch Works Backward (July 2026; backward roll mistaken for reversed wiring)
- Forest River Forums: Retracted awning always filling with water (January 2016; spring-loaded awning stalls, water in the roll)
- Jayco Owners Forum: Is my awning rolled up backwards? (August and October 2012; the doorway hand test)
How we write our guides: figures are typical US ranges checked against manufacturer documentation, published standards and installer pricing. Read our editorial standards. Spotted an error or outdated detail? Request a correction.